UDEMY Arduino Build your own Iron Man Arm with Voice Recognition BOOKWARE-iLEARN

iLEARN
source: https://www.udemy.com/course/arduino-build-your-own-bionic-arm-with-voice-recognition/
looking for locations in:
10 GBit .SE
10 GBit .NO
and other european locations

118M	1. Course Preview.mp4
125M	10. Electronic parts placement on the 3d models.mp4
81M	11. Connecting the arm first 3d parts together.mp4
226M	12. Uploading Sounds to the Sound Card memory.mp4
385M	13. Connecting the Speakers to the Sound Card.mp4
905M	14. Connecting the Sound Card to the Arduino.mp4
58M	15. Load Voice recognition programming software.mp4
158M	16. How to connect the Voice Recognition to FTDI (USB to Serial) unit.mp4
102M	17. How to Record your commands to the Voice recognition + Code commands.mp4
690M	18. Connecting the Voice Recognition to the Arduino.mp4
615M	19. Load the Arduino with program that checks that Voice recognition controls sounds.mp4
93M	2. Bionic Arm building course go through.mp4
230M	20. Running a 360 degrees servo vs regular servo, example code for Arduino.mp4
701M	21. Connecting the rubber band minigun 3d parts with 360 servo motor.mp4
133M	22. Connecting the rubber band minigun to the Bionic Arm 3D Parts.mp4
361M	23. connecting the back hatch regular servo to the 3d parts.mp4
962M	24. connecting the side Hatch regular servos to the 3d parts.mp4
1.4G	25. Connecting the wires of the 4 servos to the arduino.mp4
621M	26. Upload to the Arduino with program and check the Hatch opening and shooting.mp4
235M	27. Glue the Servo motor to the bionic arm and to the hatch front cover.mp4
413M	28. Connecting the wires needed to the front servo and the laser.mp4
327M	29. Glue the Two KY-008 Lasers+wiring to arduino.mp4
163M	3. Parts List + where to buy list(must watch before starting!).mp4
215M	30. Program the Arduino with code to check the Servo Motor and the Lasers.mp4
427M	31. Gluing 6 Leds on the Hand part(note the polarity before gluing).mp4
466M	32. Connecting the leds together by the schematic.mp4
362M	33. Connect the Leds to the Mosfet RFP30N06LE and 22ohm Resistor.mp4
212M	34. Connect wires and glue the Accelerometer MPU6050 to the Hand 3d part.mp4
942M	35. Connect the Fingers 3d parts and the glove to the Hand 3d part.mp4
207M	36. Connecting the hand cover 3d part to the hand 3d part.mp4
527M	37. Connect wires from the MPU and the Leds to the arduino.mp4
104M	38. How to run the MPU6050.mp4
281M	39. Test that the MPU controls leds and the Lasers+their Servo motor.mp4
43M	4. Install Arduino coding software.mp4
759M	40. Connect the Batteries Power Source+The Capacitor+micro switch.mp4
310M	41. placing the arduino + the sound card+ the voice recognition module.mp4
78M	42. glue the elbow 3d part and the speakers to the elbow.mp4
143M	43. Loading my sounds to the sound card+Recording my commands to voice recognition.mp4
180M	44. Introduction to the Full Arduino code.mp4
63M	45. Uploading the Code to the Arduino.mp4
51M	46. Glue the arduino cover 3d part.mp4
128M	47. Test the Arm, and have fun with it.mp4
27M	48. Bonus Lecture.mp4
200M	5. Forearm 3d parts and explanation + sources attached.mp4
66M	6. Hatch door 3d parts and explanation + sources attached.mp4
77M	7. Hand 3d parts and explanation + sources attached.mp4
159M	9. The electronic parts overview.mp4
15G	total